Ripple tank diffraction1/12/2024 Let us consider the first rays a and b, incident on adjacent slits as shown in Figure 7. If light is incident on this plate, a pattern of narrow bright fringes is produced, as shown in Figure 6.įigure 6 shows a parallel beam of monochromatic light incident normally on a diffraction grating, in which the spacing between adjacent slits is d. This approximation does not apply for sound or water waves, where the diffraction angles are larger and the wavelength may be closer in magnitude to the width of the slit.Ī diffraction grating is a plate on which there is a very large number of parallel, identical, very closely spaced slits. Where n is a whole number and is the order of the dark fringe counting outwards from the centre.įor light waves, the width of the aperture is very small and hence the diffraction angle, θ is also very small. This is the condition for the first dark fringe at angle θ. A pattern of dark and bright fringes is also formed along the central region. It can be noted that the intensity is concentrated in the central region. Intensity graphs of the diffraction pattern as a function of the angle θ, at which the light is viewed, is shown in Figure 5 below. Every wavelet spreading from the top half of the slit can be paired with the one coming from a point a/2 below, in the lower half of the slit. The above explanation can be extended to the whole of the slit. This is called destructive interference and results in dark fringes.įigure 4: Wavefront Diffracted at a Single Slit To either side of the central fringe, there are directions where the path difference between the waves from A and B are an odd number of half-wavelengths. The condition for constructive interference is that the path difference should be a whole number of the wavelengths. Constructive interference creates a bright fringe in the centre of the pattern. The two sources produce wavelets that spread out and the overlapping points create an interference pattern. B is at a distance a/2 along the wavefront from A. A is a source at the top edge of the slit and another one is B, at the centre of the slit. Each point on the wavefront passing through the slit can be considered to be a source of secondary wavelets. It can be noted that the wavelength of the wavefront remains the same during diffraction.įigure 4 shows a plane wavefront diffracted at a single slit of width a. But, if the size of the aperture is approximately equal to the wavelength, the wavefront becomes circular, with the centre on the slit. In this case, the size of the aperture is larger than the wavelength of the wavefront, the effect of diffraction is relatively small and the wavefront is curved only at the edges. In the case of a plane wavefront, if it is restricted by passing through an aperture, some of the wavelets forming the wavefront are removed, and hence the edges of the wavefront are curved. The construction of a circular wavefront is shown in Figure 3.įigure 3: Construction of a Circular Wavefront The tangent curve of the wavefronts produced by the secondary sources gives the new position of the original wavefront. He suggested that, at any instant, all points on a wavefront could be regarded as a secondary disturbance, giving rise to their own outward-spreading circular wavelets. This behaviour is explained by Huygens using the wave theory of light. When a single drop of water falls into a ripple tank, a circular wavefront will spread outwards from the disturbance. The greatest effect occurs when the wavelength is about the same size as the aperture.įigure 2: Diffraction at Different Size of Aperture It can be noted that the extent of the diffraction depends on the width of the gap compared with the wavelength. In Figure 2, diffraction is illustrated with two different sizes of aperture. The fact that light exhibits diffraction is a proof that light has wave properties. When light travels through an aperture or passes the edge of an obstacle, it deviates from the straight-line direction and appears to spread out. Diffraction of a light wave is illustrated in Figure 1.ĭiffraction may also occur at an edge. Diffraction is defined as the spreading of a wave into regions where it would not be seen if it moved only in straight lines after passing through a narrow slit or past an edge. This spreading out is called diffraction. When waves pass through a narrow gap, they spread out.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |